Most viewed - Files and Images for rebeldroids.net

Home > Member Galleries > kresty

Most viewed - kresty's Gallery

Springy cord for fusion reactor2 views

Priming Fusion Generator Parts2 views

Oops, my hole had a support in the way.2 views

Fixing support hole.2 views

Playing with Fusion Generator Coils2 views

Fusion Generator "windows" with tabs & slots2 views

2 views

Exploded view - Laras new H015 Omniwheel mount.2 viewsEach side has a 10x26x8 bearing, some spacers. Square shaft in the middle. Coupler in the motor fitting side. Have to attach motor to housing first or it'll be a pain to attach the screws.

2 views

Test fit some DRK-1 Parts2 views

"Oil Can" Picture for Photogrammetry2 viewsOne of a lot of pix Kresty took so Savage could make a model.

Dio Starts to have a head2 viewsLara wanted a new nose.

Lego D-O's outer rings2 viewsTo get the studs printed so the lego can attach I printed the outer ring/disc in 3 layers, plus the main drive wheel

Dio Counterweight, nearly 2Kg2 views

Dio's Starting to Take Shape2 viewsJust laying the head on the neck on the rims. Obviously no wheel, but he's starting to get there. (and he doesn't fall over with his head on top!)

Servo and Parts for Dio's... Nose?2 viewsSince the two-part head nose spun so readily, Lara asked if it could rotate. Nikita's like "It doesn't do that in the movie dad!"

What, his nose wiggles?2 viewsSince the two-part head nose spun so readily, Lara asked if it could rotate. Nikita's like "It doesn't do that in the movie dad!"

Working on the L3-G0 and BB-8 platform design.2 views

2 viewsUpdated rendering of wall display area plan

Trial of the lights2 views

Caulking the lenses2 views

Lara working on MCK-Y1 viewsLara starting work on her Lego MSE-6 Mouse Droid

1 views

1 views

1 views

1 views

1 views

Well, it's a ball with some orange marks on itl.1 viewsInsanity

Orientation of panels on a BB-81 viewsOrientation of panels on a BB-8

Initial attempt at Hatch 31 views

Dimensions I'm using for rings.1 views

Broken Magnet while assembling DMM (Dome Magnet Mount)1 viewsI was trying to figure out which side was North, and the test magnet flew out of my hands the last inch and sacrificed itself on the larger magnet. One bit went flying past my head 'cause I heard it hit the wall.

Lego BB-8 Dome Magnet Mount Cap Cover.1 viewsThis gets put on the Magnet Mount to mount the rest of the dome for it, and to keep the bearings and magnets where they belong. Not sure I trust it by itself to hold the magnets.

We used the Body Magnet Mount (BMM) to hold the magnets away from the wood1 views

The gap, holding them for temporary storage1 views

Same photo wider angle lens1 views

I think the toolbox droid is near this engine1 viewsfrom http://starwarsscreencaps.com/star-wars-episode-vii-force-awakens-2015/80/

Lego BB-8 Driving us around1 views He thinks this drive is on the "right" side.

Lego BB-8 Driving us around1 viewsBetter than Tesla autopilot? He thinks this drive is on the "right" side.

MCK-Y the Lego Mouse Droid and a Castle1 viewsLego Mouse Droid and Castle

Showing how corners line up1 views

Lego Greebles for H-015 Sentry Droid1 views

Lego Greeble instructions B for H-015 Sentry Droid1 views

Lego Greeble instructions D for H-015 Sentry Droid1 views

Lego Greeble instructions F for H-015 Sentry Droid1 views

Lego Greeble instructions H for H-015 Sentry Droid1 views

Lego Greeble instructions J for H-015 Sentry Droid1 views

Perhaps a filler top bit could work on the corners to adjust for sizes?1 viewsCorner top bit

The Lego Greeble Position WRT the Skiert on the Sentry Droid1 viewsThe Lego is recessed under the skirt. There is a solid row of bricks, and the smooth tiles on the bricks below that row are about flush with the edge of the skirt.

Test print of 3D Printed Antenna #21 viewsIf all you have is a hammer, everything looks like a nail. And we have a 3D printer and we don't have sheet styrene right now...

Wondering about extra lines in Fusion plans.1 viewsFor the one with the lines in the middle, it's a slot for the vertical parts to seat in. For the one with lines at the edge, it's supposed to be rounded off there.

Question about Rings for Fusion Generator1 viewsThe answer is that it's the top picture: One ring with two inner grooves/to put other bits.

Proposed Lettering of Fusion Parts1 views

3D printed H015 Antenna1 viewsFrom the 3D files in http://www.rebeldroids.net/gallery/thumbnails.php?album=63 - but apparently I posted those in the wrong spot!