Most viewed - Construction Plans
|
228 viewsYou'll also need the 3D parts at
http://www.rebeldroids.net/gallery/thumbnails.php?album=75
Wiki page for the Fusion Generator at http://www.rebeldroids.net/wiki/index.php?title=Fusion_Generator
And a few Q&A in the thread at http://www.rebeldroids.net/forum/showthread.php?tid=277
|
|
Treadwell base205 views
|
|
MSE upper shell flatpack200 views
|
|
Treadwell logic housing186 views
|
|
Treadwell head180 views
|
|
V3 Alternate Plat Pack Files intended for 18x24 Laser Cutter178 viewsThis is the V3.0 version of the 18x24 Laser Cutter plans, updated with more accurate directions! And I put scales on the sheets too!
V2: Fixed scaling problems
V2.1: Added squares for E band.
V3.0: Added tabs & slots for window area, removed lower band, added mount holes for T hose fittings on M band.
|
|
Treadwell neck177 views
|
|
Treadwell wheels diameter174 views
|
|
Treadwell body173 views
|
|
Treadwell treads172 views
|
|
Treadwell wheels details160 views
|
|
MSE lower shell flatpack146 views
|
|
© Frank Cerny Training Droid Remote140 viewsIncluded here with Mr. Cerny's permission (thanks Frank!)
Instructions for Scratch building a training droid remote
|
|
137 views
|
|
136 views
|
|
135 views
|
|
112 views
|
|
109 views
|
|
Draft Training Remote Parts Outlines108 viewsI haven't built these, so they may not be correct. Got dimensions from 3D model, seem to agree with Frank's instructions, but could be wrong.
Not complete for CnC or laser, need laid out better.
|
|
107 views
|
|
106 views
|
|
100 views
|
|
95 views
|
|
Kresty's MSE-6 Flat Pack91 viewsCut out of 1.5mm or 1/16" (poly)styrene. Does not include top or side greeblies, get creative!
|
|
Skirt Annotated Dimensions87 viewsI needed dimensions, so I added them to a PDF imported from Savage's plans. Not 1:1 scale: Reduced to print on Letter paper
|
|
87 views
|
|
.stl files to print the eye lens frames as seen in Star Wars83 viewsThese files, when assembled, recreate the internal focus lens of the Paterson Trident slide viewer which was used for the eye lenses of the Treadwell droid. The lens is not included. (see included image)
|
|
83 views
|
|
Treadwell wheel notches82 views
|
|
antenna template sheet 0180 viewsFirst revision of H015 Antennae
by savagecreature
|
|
Not sure if I can laser cut the fins80 viewsAn (alpha) attempt at cutting (vs printing) the fins for the fusion generator.
|
|
79 views
|
|
78 views
|
|
skirt template sheet 0277 viewsFirst revision of H015 outer shell
by savagecreature
|
|
skirt template sheet 0174 viewsFirst revision of H015 outer shell
by savagecreature
|
|
72 views
|
|
72 views
|
|
Alignment Guides for Greeblie Placement72 viewsI used this to figure out where those 32 greebles go around the angled ring.
|
|
70 views
|
|
head template sheet 0169 viewsFirst revision of H015 outer shell
by savagecreature
|
|
3D Models - obj, stl & skp for the Lego Greebles69 viewsI tried to "repair" them, but you know how importing/exporting/converting all these things goes. The .skp file I think is very good and accurate (but 3D builder still wanted to repair it).
|
|
Fusion generator K ring on top of J ring68 viewsThe K ring is glued directly on top of the top J ring
|
|
Shawn's 3D Model of H015 Sentry Droid67 viewsThis is a fairly accurate 3D model of the outer shell of the sentry droid. It is provided in several formats.
Additionally, there's a "flat" PDF (& cdr) of the panels which can be printed at 100%. Note, however, that the panels are the front faces and don't account for the depth of whatever material you might cut, so you'll either need to cut them a hair smaller, or sand/fill, etc. if you try to use those to build a model.
The "skirt" fits over the Lego greeblies in this version.
|
|
body template sheet 0166 viewsFirst revision of H015 outer shell
by savagecreature
|
|
head template sheet 0265 viewsFirst revision of H015 outer shell
by savagecreature
|
|
Lego Bottom Greebles Construction Plans65 viewsLego Digital Designer Files and png steps for the Lego Greeble construction
|
|
antenna template sheet 0260 viewsFirst revision of H015 antennae
by savagecreature
|
|
Bottom Greebles STL Split59 viewsSTL Split into halves and also thirds. I haven't tried printing, so not sure how well they work.
|
|
K Ring on Top of J Ring - Fusion Generator Contruction58 views
|
|
construction plans zip archive57 viewsThe first set of construction plans in a .zip file
|
|
NON-PLANS for Lego Mouse Droid55 viewsJust enough of a file to get people into trouble
|
|
54 views
|
|
Experimental 3D Printable H015 Antennae STL50 viewsWell, the flat pack seems easy enough that it seems silly to print the H015 antennae - but if you want to try, this might work.
|
|
46 views
|
|
H015 Motor Wiring Diagram45 viewsPDF showing how I connected the Simple Motor Controllers and the Arduino and the R/C Receiver
|
|
36 views
|
|
27 views
|
|
Adventures of Building a D-O (rev 1)27 viewsMat Prentis's Dio build info, detailed notes for Mat's build from Mr Baddeley's design.
|
|
25 views
|
|
BB-8 Stand Zip of Plans15 viewsKresty (Shawn's) plans for a BB-8 stand, themed with the imperial grid pattern that shows up everywhere in Star Wars.
|
|
|