Image search results - "lego" - Files and Images for rebeldroids.net

Image search results - "lego"

Servo and Parts for Dio's... Nose?2 viewsSince the two-part head nose spun so readily, Lara asked if it could rotate. Nikita's like "It doesn't do that in the movie dad!"

What, his nose wiggles?2 viewsSince the two-part head nose spun so readily, Lara asked if it could rotate. Nikita's like "It doesn't do that in the movie dad!"

Dio's Starting to Take Shape2 viewsJust laying the head on the neck on the rims. Obviously no wheel, but he's starting to get there. (and he doesn't fall over with his head on top!)

Kresty's Droids at ECCC 20231 viewsLego BB-8, D-O, H-O15 Sentry, MCK-Y, Toolbox, L3-G0

Lego Greebles for H-015 Sentry Droid2 views

Lego Greebles for H-015 Sentry Droid1 views

Lego Greebles for H-015 Sentry Droid0 views

Lego Greeble instructions A for H-015 Sentry Droid2 views

Lego Greeble instructions B for H-015 Sentry Droid1 views

Lego Greeble instructions D for H-015 Sentry Droid1 views

Lego Greeble instructions E for H-015 Sentry Droid0 views

Lego Greeble instructions F for H-015 Sentry Droid1 views

Lego Greeble instructions G for H-015 Sentry Droid0 views

Lego Greeble instructions H for H-015 Sentry Droid1 views

Lego Greeble instructions I for H-015 Sentry Droid0 views

Lego Greeble instructions J for H-015 Sentry Droid1 views

Lego Greeble instructions K for H-015 Sentry Droid0 views

Lara working on MCK-Y2 views

Lara working on MCK-Y1 viewsLara starting work on her Lego MSE-6 Mouse Droid

Dio Starts to have a head2 viewsLara wanted a new nose.

Broken Magnet while assembling DMM (Dome Magnet Mount)1 viewsI was trying to figure out which side was North, and the test magnet flew out of my hands the last inch and sacrificed itself on the larger magnet. One bit went flying past my head 'cause I heard it hit the wall.

We used the Body Magnet Mount (BMM) to hold the magnets away from the wood1 views

The gap, holding them for temporary storage1 views

Lego BB-8 Dome Magnet Mount Cap Cover.1 viewsThis gets put on the Magnet Mount to mount the rest of the dome for it, and to keep the bearings and magnets where they belong. Not sure I trust it by itself to hold the magnets.

What a mess3 viewsMy full size Lego BB-8 hanging around his construction area

Lego BB-8 mostly complete!!!4 viewsMy full size Lego BB-8

Lego Bottom Greebles Construction Plans65 viewsLego Digital Designer Files and png steps for the Lego Greeble construction

Dio Starts to have a head1 viewsFinally have the cone part working

Thoughts about a Lego version of D-O's head0 viewsThinking about D-O's head, trying to see how a cone might work. The tiles seem to be about right. Wedges didn't really come close enough. Longer tiles leave too much space.

NON-PLANS for Lego Mouse Droid58 viewsJust enough of a file to get people into trouble

Tracks (maybe) for Toolbox Droid1 viewsPlaying around with models.

Printed hub and parts for assembly0 viewsPrinted hub and parts for assembly

Wheel and hub with 'socket' driver on nut0 viewsMy hole was too small, so this was printed to put the nut in.

Wheel and Lego Printed Hub2 viewsHub and nut on the car

Chassis of MCK-Y with Lego wheels.4 viewsUsing an RC chassis with printed hubs to attach Lego wheels

Inside of printed hub0 viewsInside of printed hub - hex pattern goes on driveshaft -- Front wheel hubs are shorter, no nuts, not sure how they'll stay on, may need epoxy.

Outside of printed hub0 viewsHole for nut and shows technic pins and pin holes (to attach lego wheel). Front wheel hubs are shorter, no nuts, not sure how they'll stay on, may need epoxy.

Nut and socket to screw it in0 viewsWorked to get the rear wheels finger tight anyway. Hope that's enough

Rear Lego wheel on printed hub0 viewsLonger than front wheel

Front Lego wheel on printed hub0 viewsshorter than rear wheel

Shock with spacer and without spacer2 viewsSpacers in the middle are needed so the shocks don't go down so far since MCK-Y is so heavy.

Why the shocks need spacers2 viewsShowing the shocks with & without spacer installed. Spacer keeps it from compressing as far. There's still a rubber stop so it can damp some vibration.

Lego D-O's outer rings2 viewsTo get the studs printed so the lego can attach I printed the outer ring/disc in 3 layers, plus the main drive wheel

Lego D-O's outer rings1 viewsTo get the studs printed so the lego can attach I printed the outer ring/disc in 3 layers, plus the main drive wheel

Well, it's a ball with some orange marks on itl.1 viewsInsanity

Center of Sentry Droid bottom greebles3 viewsFinding the center of a side of bottom Lego greebles

Omniwheel and Lego Greebles of Sentry Droid41 views

Omniwheel, Lego Greebles and Faux Wheels of Sentry Droid45 views

Lego Greebles of Sentry Droid44 views

Sentry Droid34 views

40 views

35 views

Lego underneath Sentry Droid40 views

Cast Lego bricks on bottom of Sentry Droid4 viewsThis is the droid that "they tried to blow up" according to Oliver. Oliver used Lego on the bottom for details, then they were molded and cast from Resin. Caught this pix underneath him as he was being lifted off the stage.

Lego Toolbox Droid Top Platform Construction0 viewsHolding the top of the droid over the wheels about where it goes.

Lego Toolbox Droid Top Platform Construction0 viewsWorking on the tippy top of the Toolbox Droid

3D Rendering of the toolbox drivetrain0 viewsI rendered spaces for the battery, motors, etc to make sure they fit. The board is laser cut.

Trial Corner of Toolbox Droid top0 views

Lego Toolbox Droid Top Platform Construction0 viewsOne of the tracks is on, mostly assembled.

Lego Toolbox Droid Track0 views

Lego Toolbox Droid Track Color Test0 views

Wheel with Tracks0 viewsWheel was supposed to have 10 segments of track fit around it. It's a bit too small.

Lego Toolbox Droid Printing Last Wheel0 viewsSomehow one of the wheels got missing. Good test of the new cabinet for the CR-10, my Flashforge isn't big enough for this. Worked well until I decided it was done a little too soon. (It'll be usable though).

69 files on 1 page(s)