Image search results - "fusion" - Files and Images for rebeldroids.net

Image search results - "fusion"

Kresty's Fusion Reactor2 views3D Printed vs Laser Cut top vanes

Alignment Guides for Greeblie Placement72 viewsI used this to figure out where those 32 greebles go around the angled ring.

Kresty's Fusion Reactor2 viewsAssembling the top

Kresty's Fusion Reactor1 viewsAssembling the top

Kresty's Fusion Reactor2 viewsBad layers printed flat

Kresty Fusion Reactor Base Build2 views

Kresty Fusion Reactor Base Build1 views

Fusion Generator plugged in.21 viewsMy first guess was 1/4" audio jack, but XLR makes more sense considering they'd be all over the place on a movie set. The fitting looks overly complicated for that though, an adapter?

Fusion Reactor Top Primed3 views

Fusion Reactor Top Bare2 views

Fusion Reactor Light Test2 views

Fusion Reactor Light Test1 views

Kresty's Fusion Reactor1 viewsKresty's Fusion Reactor Top

Main Hose Mount2 views

How Nipple Connects Hose and Tee2 views

Fusion generator K ring on top of J ring68 viewsThe K ring is glued directly on top of the top J ring

V3 Alternate Plat Pack Files intended for 18x24 Laser Cutter178 viewsThis is the V3.0 version of the 18x24 Laser Cutter plans, updated with more accurate directions! And I put scales on the sheets too!

V2: Fixed scaling problems
V2.1: Added squares for E band.
V3.0: Added tabs & slots for window area, removed lower band, added mount holes for T hose fittings on M band.

Light Concept1 views

Light Leak on Top2 views

Light Leaks4 views

Middle "Grill" assembly of fusion generator0 viewsUnglued middle section

Kresty's 3D Fusion Parts (v2)131 viewsI tweaked some of Savage's 3D printed parts to make some of the bits easier for me.

Kresty's Fusion Generator5 views

K Ring on Top of J Ring - Fusion Generator Contruction58 views

Close up of Fusion Generator and Plug31 viewsCropped and Magnified from Still

Printed Hose Fitting on 1/4" Jack1 views

Kresty's Fusion Reactor2 viewsTest fit of base

Fusion Generator Initial Test Assembly3 viewsNot glued completely, but showing where the main sections go!

Fusion Generator Initial Test Assembly1 viewsNot glued completely, but showing where the main sections go!

Kresty's Fusion Reactor2 viewsTop test fit

Kresty's Fusion Reactor1 viewsTop test fit

Kresty's Fusion Reactor1 viewsTab fittings

Kresty's Fusion Reactor1 viewsTab and guide fittings

Zoom in on unlit Fusion generator.21 viewsThe cord is looping down and the end's apparently just been jammed behind one of the hoses so Mark Hammil can grab it easily.

Unlit Fusion Generator20 viewsUnlit Fusion Generator, prior to plugging in.

Fusion Generator unlit15 views

Unlit and all wrapped up24 viewsFusion Generator looks like the cords are all wrapped up so they don't get tangled. The "plug" looks different in this picture, like there's a dual banana connector adapter on the end.

Kresty's Fusion Reactor2 viewsLaser Cut vane test fit

Widening Lower Hose End3 viewsMy little hoses were too small for my posts.

Shawn's Fusion Reactor Laser Cut Parts4 views

Shawn's Fusion Reactor Laser Cut Parts1 views

Shawn's Fusion Reactor Laser Cut Parts2 views

Shawn's Fusion Reactor Laser Cut Parts1 views

Shawn's Fusion Reactor Laser Cut Parts1 viewsSmokey

48 files on 1 page(s)