02-03-2024, 10:08 AM
Blog update 23:
https://r5-d4astromechdroid.blogspot.com...3.html?m=1
Well busy week & got a lot done.
![[Image: 823d851a49d761ac5fb316ca129cbcec.jpg]](https://uploads.tapatalk-cdn.com/20240203/823d851a49d761ac5fb316ca129cbcec.jpg)
![[Image: 9b216879ab10fe7372ea658ee324e3ba.jpg]](https://uploads.tapatalk-cdn.com/20240203/9b216879ab10fe7372ea658ee324e3ba.jpg)
Machined up axles.
![[Image: 35c1368b1b208bde8f4a53eb4e68dda3.jpg]](https://uploads.tapatalk-cdn.com/20240203/35c1368b1b208bde8f4a53eb4e68dda3.jpg)
Finished machining the brass bushes.
Machined up first of the motor couplers, and later, tested to see if it (motor) had enough torque for the job!
![[Image: e5d325eb4ef0f653de372e30027c3cba.jpg]](https://uploads.tapatalk-cdn.com/20240203/e5d325eb4ef0f653de372e30027c3cba.jpg)
Body work, the two lower angles needed body filler.
![[Image: cb8193e498297d076636196bb901426d.jpg]](https://uploads.tapatalk-cdn.com/20240203/cb8193e498297d076636196bb901426d.jpg)
![[Image: 4261c5a4c5b367d203ac3196eaa5c0fc.jpg]](https://uploads.tapatalk-cdn.com/20240203/4261c5a4c5b367d203ac3196eaa5c0fc.jpg)
3D modelled and printed the two front axle cover plates and also the inner shaft location blocks.
![[Image: d5697a475dc6a3989951009f472ce611.jpg]](https://uploads.tapatalk-cdn.com/20240203/d5697a475dc6a3989951009f472ce611.jpg)
So here’s the link to the testing of the motor.
I had to hold the motor as it didn’t have a location bracket, it’s in the post.
https://youtu.be/k8deB17r8jM?si=F3yG7JT_aOB2Q9-B
Sent from my iPhone using Tapatalk
https://r5-d4astromechdroid.blogspot.com...3.html?m=1
Well busy week & got a lot done.
![[Image: 823d851a49d761ac5fb316ca129cbcec.jpg]](https://uploads.tapatalk-cdn.com/20240203/823d851a49d761ac5fb316ca129cbcec.jpg)
![[Image: 9b216879ab10fe7372ea658ee324e3ba.jpg]](https://uploads.tapatalk-cdn.com/20240203/9b216879ab10fe7372ea658ee324e3ba.jpg)
Machined up axles.
![[Image: 35c1368b1b208bde8f4a53eb4e68dda3.jpg]](https://uploads.tapatalk-cdn.com/20240203/35c1368b1b208bde8f4a53eb4e68dda3.jpg)
Finished machining the brass bushes.
Machined up first of the motor couplers, and later, tested to see if it (motor) had enough torque for the job!
![[Image: e5d325eb4ef0f653de372e30027c3cba.jpg]](https://uploads.tapatalk-cdn.com/20240203/e5d325eb4ef0f653de372e30027c3cba.jpg)
Body work, the two lower angles needed body filler.
![[Image: cb8193e498297d076636196bb901426d.jpg]](https://uploads.tapatalk-cdn.com/20240203/cb8193e498297d076636196bb901426d.jpg)
![[Image: 4261c5a4c5b367d203ac3196eaa5c0fc.jpg]](https://uploads.tapatalk-cdn.com/20240203/4261c5a4c5b367d203ac3196eaa5c0fc.jpg)
3D modelled and printed the two front axle cover plates and also the inner shaft location blocks.
![[Image: d5697a475dc6a3989951009f472ce611.jpg]](https://uploads.tapatalk-cdn.com/20240203/d5697a475dc6a3989951009f472ce611.jpg)
So here’s the link to the testing of the motor.
I had to hold the motor as it didn’t have a location bracket, it’s in the post.
https://youtu.be/k8deB17r8jM?si=F3yG7JT_aOB2Q9-B
Sent from my iPhone using Tapatalk